Star-tech-development TSP100 Manuale Utente

Hardware Manual

– 7 –3-1-2. PU ModelCAUTIONMake sure that the printer is turned off before connecting the PoweredUSB cable (Y cable) orPoweredUSB cable (straight type

– 8 –(2) Connect the interface cable to the printer as shown. When using the USB cable, secure thecable with the hook.USB cablePoweredUSB cable (Y cab

– 9 –3-2. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. The following describeshow to install

– 10 –3-3. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification.When using a paper roll with an 57.5 mm width, ins

– 11 –Note: When using a paper roll with an 57.5mm width, install the paper roll holderin the groove in the printer.If a paper roll with a 57.5 mm wid

– 12 –WARNING• Do not touch the cutter blade.- There is a cutter inside the paper outlet slot. Not only should you not put your hand in thepaper outle

– 13 –3-4. Connecting the USB/PoweredUSB Cable to the PC3-4-1. U ModelConnect the USB interface cable to a USB port of your PC.Note: The dialog shown

– 14 –Note: The dialog shown below may appear on your PCscreen if your PC is running Windows 98 or Me,and if you turn ON the power of the printer for

– 15 –3-6. Connecting the Power Cord3-6-1. U ModelNote: Before connecting/disconnecting the power cord, make sure that power to the printerand all the

– 16 –3-6-2. PU ModelNote: Before connecting/disconnecting the AC adapter, make sure that power to the printerand all the devices connected to the pri

Federal Communications CommissionRadio Frequency InterferenceStatementThis equipment has been tested and found to comply with the limits for a Class A

– 17 –Power switch3-7. Turning Power OnMake sure that the Power cord has been connected as described in 3-6.(1) Turn ON the power switch located on th

– 18 –4. Attaching the AccessoriesThe following accessories do not necessarily have to be attached.Attach them if necessary.• Holding plate• Rubber fe

– 19 –4-2. Attaching the Rubber Feet(1) Attach the four rubber feet in the positionsshown in the figure.Ensure that any soiling has been com-pletely w

– 20 –4-3. Switch Cover InstallationIt is not necessary to install the switch cover. Only install it if it is necessary for you. By installingthe swit

– 21 –5. Thermal Roll Paper SpecificationWhen consumable parts have run out, use those specified below.5-1. Roll paper specificationThermal paperThick

– 22 –5-2-2. PU ModelNote:Access the following URL for the information of the recommended paper.http://www.star-m.jp/eng/dl/dl02.htmManufacturerMitsub

– 23 –6. Control Panel and Other Functions6-1. Control Panel1 POWER lamp (Green LED)3 FEED button2 ERROR lamp (Red LED)1 POWER lamp (Green LED)Lights

– 24 –2) Non-recoverable errorsError DescriptionHead thermistor errorBoard thermistor errorVM voltage errorVCC voltage errorEEPROM errorUSB errorCPU e

– 25 –6-3. Self-PrintingTest PrintingTurn the power ON while holding the FEED button depressed. Test printing is performed. Theversion number and prin

– 26 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper JamsThe paper should not be touched during ejection and before it is cut.Pressing or

TABLE OF CONTENTS1. Unpacking and Installation ...

– 27 –7-3. Releasing a Locked Cutter (Auto Cutter Mode only)If the auto cutter locks up or fails to cut the paper, follow the steps below.WARNINGSince

– 28 –(4) If the cutter is locked, insert a Philips screwdriver into the Philips screw hole on the side ofthe cutter, and turn it in the direction of

– 29 –8. Periodical CleaningPrinted characters may become partially unclear due to accumulated paper dust and dirt. Toprevent such a problem, paper du

– 30 –ECR3 R4R3= 3.5kΩR4= 300ΩBModular plugPin No.SignalFunctionI/Oname direction1 FG Frame ground —2 DRD1 Drive signal 1 OUT3 +24V Drive power OUT4 +

– 31 –Notes: 1. Pin 1 must be shield drain wire connected to peripheral device frame ground.2. It is not possible to drive two drives simultaneously.3

– 32 –10. Specifications10-1. General Specifications(1) Printing method Direct line thermal printing(2) Print speed Max. 1000 dots/sec. (125 mm/sec.)(

– 33 –10-4. Electrical Characteristics10-4-1. U Model(1) Input Voltage 100 to 240 V AC, 50/60 Hz(2) Current Consumption Operating: Approx. 40 W (at AS

– 34 –(4) Power ConnectorNotes:• When using a printer power supply other than the optional AC adapter (PS60A-24Aseries), be sure that the following ca

– 35 –10-4-3. PU Model (PoweredUSB cable)When using the PoweredUSB cable, DC 24 V must be supplied to the printer from the system.Use a power supply f

– 36 –(%RH)34°C90% RH40°C65% RH45°C50% RH90806040201001020Temperature (°C)Operating environmentrangeRelative humidityOperating temperature and humidit

– 1 –PrinterPaper roll holderHolder plateSwitch coverUSB cablePower cordRubberfeetCD-ROMInstallation sheetRoll paperScrewsFerrite core1. Unpacking and

– 37 –10-6. Reliability1) Life Mechanical: 20 million linesHead: 100 million pulses, 100 km (±15% max. average head resistancefluctuation)For 2-color

– 38 –11. DIP Switch SettingsThere are DIP switches located on the bottom of the PU model printers and various settings canbe performed as shown in th

2006.12.31Printed in China, 80870492CDELECTRONIC PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinya, Shimizu-ku, Shizuoka,424-0066 JapanTel: 0

– 2 –1-1-2. PU ModelPaper roll holderHolder platePrinterSwitch coverScrewsRubber feetRoll paperConnector cover ACD-ROMInstallation sheet[Options]AC ad

– 3 –2. Parts Identification and Nomenclature2-1. U ModelCover open leverPull this lever in thedirection of the arrow toopen the printer cover.Control

– 4 –2-2. PU ModelCover open leverPull this lever in thedirection of the arrow toopen the printer cover.Peripheral drive connectorConnects to peripher

– 5 –2-3. Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about whereyou plan to use it.

– 6 –3. Setup3-1. Connecting the USB/PoweredUSB Cable to the Printer3-1-1. U ModelAffix the ferrite core onto the USB interface cable and pass the cab